ISL6119USBEVAL1【PDF 1/13 页】EVALUATION BOARD FOR ISL6119

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1222

[1页]2页 3页 4页 5页

ISL6119

Data Sheet

March 2004

FN9002.3

USB Dual Port Power Supply Controller

The ISL6119 is a USB dual port power controller, fully

independent overcurrent (OC) fault protection IC.

Operational over the +2.5V to +5.5V range, this device

features internal current monitoring, accurate current

limiting, integrated power switches and current limited

delay to latch-off for system protection.

The ISL6119 current sense and limiting circuitry sets the current

limit to a nominal 1A, making this device well suited for the USB

port power management application. The ISL6119 provides OC

fault notification, accurate current limiting and a consistent

timed latch-off thus isolating and protecting the voltage bus in

the presence of an OC event or short circuit. The 12ms time to

latch-off is independent of the adjoining switch’s electrical or

thermal condition and the OC response time is inversely related

to the OC magnitude.

Each ISL6119 incorporates in a single 8 lead SOIC

package two 80m ? N-channel MOSFET power switches

for power control. Each switch is driven by a constant

current source giving a controlled ramp up of the output

voltage. This provides a soft start turn-on eliminating bus

voltage drooping caused by inrush current while charging

heavy load capacitances. Independent enabling inputs and

Features

? 80m ? Integrated Power N-channel MOSFET Switches

? Accurate Current Sensing and 1A Current Limiting

? 12ms Fault Delay to Latch-Off, No Thermal Dependency

? 2.5V to 5.5V Operating Range

? Disabled Output Internally Pulled Low

? Undervoltage Lockout

? Controlled Turn-on Ramp Time

? Channel Independent Fault Output Signals

? Compatible with 3.3V and 5V Logic Families

? Channel Independent Logic Level Enable High Inputs

(ISL6119H) or Enable Low Inputs (ISL6119L)

? Pb-Free Package Options

? Available in Tape & Reel with ‘-T’ Part Number Suffix

Applications

? USB Port Power Management

? Electronic Circuit Limiting and Breaker

Ordering Information

fault reporting outputs for each channel are compatible with

3V and 5V logic to allow external control and monitoring.

The ISL6119 undervoltage lockout feature prevents turn-on

PART

NUMBER

ISL6119LIB

TEMP.

RANGE (°C)

-40 to 85

PACKAGE

8 Lead SOIC

PKG.

DWG. #

M8.15

of the outputs unless the correct ENABLE state and VIN >

2.5V are present. During initial turn-on the ISL6119

ISL6119LIBZA

(Note)

-40 to 85

8 Lead SOIC (Pb-free) M8.15

prevents fault reporting by blanking the fault signal. Rising

and falling outputs are current limited voltage ramps so that

both the inrush current and voltage slew rate are limited,

independent of load. This reduces supply droop due to

surge and eliminates the need for external EMI filters.

ISL6119HIB

ISL6119HIBZA

(Note)

ISL6119EVAL1

-40 to 85 8 Lead SOIC M8.15

-40 to 85 8 Lead SOIC (Pb-free) M8.15

Evaluation Platform

During operation, once an OC condition is detected the

appropriate output is current limited for 12ms to allow

transient conditions to pass. If still in current limit after the

current limit period has elapsed, the output is then latched

off and the fault is reported by pulling the corresponding

FAULT low. The FAULT signal is latched low until reset by

the ENABLE signal being de-asserted at which time the

ISL6119USBEVAL1 USB Dual Port Evaluation Platform

NOTE: Intersil Pb-free products employ special Pb-free material

sets; molding compounds/die attach materials and 100% matte tin

plate termination finish, which is compatible with both SnPb and

Pb-free soldering operations. Intersil Pb-free products are MSL

classified at Pb-free peak reflow temperatures that meet or exceed

the Pb-free requirements of IPC/JEDEC J Std-020B.

FAULT signal will clear.

Pinout

ISL6119 (SOIC)

TOP VIEW

GND

VIN

ENABLE_1

ENABLE_2

FAULT_1

OUT_1

OUT_2

FAULT_2

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式